Stewart Systems Ekoprime Primer / Sealer

от 12989 10825 руб.

до 59797 49831 руб.

Наличие: Проверяйте наличие по каждому товару

Типы

Артикул
Название
Цена за ед.
Кол-во
Цена
09-03075 7520SS EKOPRIME SMOKE GRAY GL 50643 42203 руб. 0.000.00 руб.
09-03075-HP 7520SS EKOPRIME SMOKE GRAY GL W/ HEAT PACK 44974 37479 руб. 0.000.00 руб.
09-03074 7520SS EKOPRIME SMOKE GRAY QT 15278 12732 руб. 0.000.00 руб.
09-03074-HP 7520SS EKOPRIME SMOKE GRAY QT W/ HEAT PACK 15343 12786 руб. 0.000.00 руб.
09-03077 7525SS EKOPRIME CHARC GRAY GL 51423 42853 руб. 0.000.00 руб.
09-03077-HP 7525SS EKOPRIME CHARC GRAY GL W/ HEAT PACK 46535 38779 руб. 0.000.00 руб.
09-03076 7525SS EKOPRIME CHARC GRAY QT 14810 12342 руб. 0.000.00 руб.
09-03076-HP 7525SS EKOPRIME CHARC GRAY QT W/ HEAT PACK 12989 10825 руб. 0.000.00 руб.
09-03079 7530SS EKOPRIME ZC GREEN GL 59797 49831 руб. 0.000.00 руб.
09-03079-HP 7530SS EKOPRIME ZC GREEN GL W/ HEAT PACK 54336 45280 руб. 0.000.00 руб.
09-03078 7530SS EKOPRIME ZC GREEN QT 19751 16459 руб. 0.000.00 руб.
09-03078-HP 7530SS EKOPRIME ZC GREEN QT W/ HEAT PACK 17813 14844 руб. 0.000.00 руб.
09-00481 STEWART SYSTEMS PRIMER SEALER GL 48043 40036 руб. 0.000.00 руб.
09-00481-HP STEWART SYSTEMS PRIMER SEALER GL W/ HEAT PACK 53036 44196 руб. 0.000.00 руб.
09-00464 STEWART SYSTEMS PRIMER SEALER WHITE QT 13978 11648 руб. 0.000.00 руб.
09-00464-HP STEWART SYSTEMS PRIMER SEALER WHITE QT W/ HEAT PACK 15733 13111 руб. 0.000.00 руб.

Итого: 0.000.00 руб.

Overview

With Heat Pack option adds a shipping heat pack to keep the material from freezing while in transit. It is recommended for winter months / destinations in cold climates where the temperature may drop below freezing while in transit. If the material freezes, it is not recommended for use.


Stewart Systems Primer Sealer is a high quality, water-based single component primer, not requiring any catalyzing agent. Performance obtained is equal or superior to that of two-component, catalyzed epoxy systems. Primer Sealer offers good coverage, excellent durability, and ease of application, as well as being a low VOC and EPA compliant coating.

ENVIRONMENTAL ADVANTAGE

It is a low VOC (Volatile Organic Compound). high performance production coating. It is considered non-hazardous by EPA definitions and does not contain lead or chromates. The solid and semi-solid sludge produced in spraying and clean up can be flocculated; dried and sent to a "Class B" landfill. Check with your local and state regulations for proper handling.

CHARACTERISTICS

  • Excellent exterior durability
  • Excellent hardness/impact resistance
  • Excellent mar and abrasion resistance
  • Excellent adhesion on plastics, gelcoat and composite substrates
  • Solvent resistant
  • Can be applied in a wide variety of temperature and humidity conditions without the use of retarders
  • Distilled water is used for reduction
  • Water is used for clean-up
  • Non-Hazardous
  • Air dry or force curing preferred
  • Can be oven baked
  • Wide range of colors to promote topcoat coverage
  • Coating will not flash rust on bare metal
  • Shelf life of 1+ years
  • Unused paint can be returned to container
  • Non-Flammable

USES

  • Steel, Aluminum, Fiberglass, Wood, Plastics, Concrete, PVC, Pre-Finished Siding, Steel Decks

AIR QUALITY DATA

  • VOC (Volatile Organic Compounds) 2.0 lb/gal; 240 gm/ltr
  • Free of lead and chromates

PHYSICAL DATA

  • Liquid Boiling Point: 336°F
  • Specific Gravity: >1
  • % Solid by weight: 43.2%
  • Vapor Density: Heavier than air
  • % Solid by volume: 40.62%
  • Evaporation Rate: Slower than ether
  • Weight per gallon: 10.36 lbs.
  • pH: 7-8.5
  • Flash Point: 150°F CC
  • VOC: 2.0 lb/gal; 240 gm/ltr

PERFORMANCE DATA

  • Theoretical Coverage at I mil: 660 ft2 (1624 x 40.62% solids by volume)

SPECIFICATIONS

  • METALS: Surface must be free of grease, oil, dirt, and other foreign matter. Oxidation material must be removed or converted with Aircraft Finishing Systems Conversion Coating.
  • FIBERGLASS: Surface must be free of grease, oil, dirt, and other foreign matter.
  • CONCRETE: Surface must be free of grease, oil, dirt, and other foreign matter.

MIXING DIRECTIONS

1. Application area temperature should be between 70 and 85 degrees Fahrenheit.
2. Mix well before using. DO NOT SHAKE...STIR ONLY Make sure any solids that might have settled to the bottom are mixed back into suspension.
3. Thin by adding 10% distilled water (by weight). SS EkoPrime Primer/Sealer may be sprayed right out of the bottle for heavy build up to fill scratches.
4. Always pour mixed and thinned primer through a medium paint filter before spraying.

SPRAY APPLICATION

1. The first coat of SS Waterborne Primer/Sealer is applied as a light tack coat. Allow to dry untill tacky.
2. Apply 2nd coat to achieve solid coverage.
3. If top coating is desired, allow to dry. Lightly sand with 320 grit open coat sandpaper or ScotchBrite with red ScotchBrite pad.

BRUSHING & ROLLING

For best results we advise spraying. But, if brushing or rolling is desired, you can achieve a nice finish with a foam brush or roller. Do not thin the primer with additional water unless it will not flow out.

CLEAN UP

Clean equipment immediately with water.