Stewart Systems Ekopoxy

от 22720 18933 руб.

до 101856 84880 руб.

Наличие: Проверяйте наличие по каждому товару

Типы

Артикул	Название	Цена за ед.
09-03066	7610SS EKOPOXY WHITE QT	24931 20776 руб.
09-03067	7610SS EKOPOXY WHITE GAL	90252 75210 руб.
09-03068	7620SS EKOPOXY SMOKE GRAY QT	25846 21538 руб.
09-03069	7620SS EKOPOXY SMOKE GRAY GL	92707 77256 руб.
09-03070	7625SS EKOPOXY CHARC GRAY QT	25846 21538 руб.
09-03071	7625SS EKOPOXY CHARC GRAY GL	96672 80560 руб.
09-03072	7630SS EKOPOXY ZC GREEN QT	31945 26621 руб.
09-03073	7630SS EKOPOXY ZC GREEN GL	101856 84880 руб.
09-03066-HP	7610SS EKOPOXY WHITE QT W/ HEAT PACK	24549 20458 руб.
09-03068-HP	7620SS EKOPOXY SMOKE GRAY QT W/ HEAT PACK	24931 20776 руб.
09-03069-HP	7620SS EKOPOXY SMOKE GRAY GL W/ HEAT PACK	85068 70890 руб.
09-03072-HP	7630SS EKOPOXY ZC GREEN QT W/ HEAT PACK	29962 24969 руб.
09-03067-HP	7610SS EKOPOXY WHITE GAL W/ HEAT PACK	82628 68857 руб.
09-03070-HP	7625SS EKOPOXY CHARC GRAY QT W/ HEAT PACK	22720 18933 руб.
09-03071-HP	7625SS EKOPOXY CHARC GRAY GL W/ HEAT PACK	85678 71398 руб.
09-03073-HP	7630SS EKOPOXY ZC GREEN GL W/ HEAT PACK	91167 75973 руб.

Итого: 00 руб.

Overview

With Heat Pack option adds a shipping heat pack to keep the material from freezing while in transit. It is recommended for winter months / destinations in cold climates where the temperature may drop below freezing while in transit. If the material freezes, it is not recommended for use.

Stewart Systems EkoPoxy Primer/Sealer is a high quality water based Epoxy primer for use on many substrates. Stewart Systems EkoPoxy can be used on interior and exterior surfaces where there is more chance of corrosion from the environment. Excellent adhesion to bare metals, resists flash rusting which can occur with latex based primers. Stewart Systems EkoPoxy has superior chemical resistance, is fast drying and mar resistant. Stewart Systems EkoPoxy is low in VOCs and compatible with a wide range of top coats including EkoPoly Top coat. Nonhazardous, nonflammable and water cleanup, Stewart Systems EkoPoxy is your best choice for Primer.

Добавить отзыв

James B 25.08.2019	I have used this on my last project and like it very much.
Tom 27.11.2015	I have previously been using a self etch zinc phosphate primer, and now that temperatures are warm enough, I have switched to using EkoPoxy. It is way less pungent (my etch primer stinks days after application) and seems to apply well (I am using it as a primer on interior components. Appears to adhere better than the etch primer (doesnt marr readily when riveting), and can be applied with a small touch up gun (0.5mm nozzle) if you add more water (+50%) to thin it (although the manufacturer recommends only applying with a 1.5-1.8mm nozzle). Only time will tell its true corrosion resisting potential. All said, Im very impressed, and its so nice not to have pungent VOCs around you the whole time (but still wear good respiratory equipment).
Darin A 09.04.2020	I decided to try this low VOC primer because Im forced to do my priming in my attached garage this time of year. It was definitely good for that purpose as there was almost no smell to it. Spraying it however is not easy. Im no professional but I have built two aluminum airplanes and have done a fair bit of priming on those aircraft and this primer is by far the hardest to get a good coat on. Its only been a little over a week since I sprayed the primer so its still not at full hardness but so far it seems like it sets up better than any rattle can primer but not quite as hard as an epoxy such as Azko (which sprays very nicely...maybe Im spoiled). Oh, one more thing, it does not appear to be compatible with JetFlex WR interior coating I use.
John G 22.06.2020	I tried applying this with a couple of different spray guns, and used a weight scale with 0.01 gram accuracy to measure, tried more and less water. No joy. When sprayed, If wet enough it runs, if not wet enough it pebbles (worse than a run because now you have to sand it all off because it did not wet out). Forget spray, go with a tiny foam roller. It wont run, and will fully wet out every pass. And, thanks to its odd quick setting action, you can recoat/reroll within minutes. I am doing a pair of c172 wingtips, with a roller I can fully roll and wet out one tip then the other and by the end of the second one then the first one is ready to recoat. Takes 4 coats but you can bang them all out with a roller about as fast as you can roll. Now let them sit overnight. In the morning they will be soft. Spray them lightly with black guide coat (lightly!) from the automobile paint store it will help with sanding. But after guide coat is applied now they are dark grey or nearly black, or at least dark so set them in the sun to bake. Do not apply a coat of guide coat, just a an incomplete light mist so the primer can breath through the guide coat. Being black/dark heats them in the sun and sets the paint HARD. 1 or 2 days in full sun. Once baked and hard sand with 220 grit just until the guide coat disappears. Nice finish now. ready for paint. No idea how to bake a whole airplane, probably cant, go on vacation for a week or two instead. Leave the hangar heat at 80f. Nice water cleanup and not stinky.
Normand 29.09.2020	I used SS primer during all my RV8 construction. Very satisfied... tough as nails primer adhesion, providing the surface is well treated prior. Removed one star as the catalist in the quart I received had thickened somewhat, though still usable. Batches IÃ¢??ve received in the past were more liquid. IÃ¢??m suspecting this batch sat on a shelf for considerable length of time before being shipped, which will likely reduce my remaining shelf life.
Kenneth E 21.10.2020	Ive used the EkoPoxy to prime my metal Zenith. When opening the product, I thought it had gone bad. You must use a powered (drill) attached mixer tip and stir 10 minutes to get a creamy texture. This is common for this product, its not bad. Add 18% by weight (grams) catalist and 13% by weight water. Mix and spray. I used a 1.3mm tip. No difficulties with spray. Primer dries quickly. Second coat in 10 minutes. This stuff is tough and durable. Sanding is necessary.